Schemc
ATC Spindle Motor 5.5KW BT30 Water Cooled Automatic Tool Changer Spindle 220V 380V CNC Machining Center Engraving And Milling
ATC Spindle Motor 5.5KW BT30 Water Cooled Automatic Tool Changer Spindle 220V 380V CNC Machining Center Engraving And Milling
Regular price
$5,920.25 USD
Regular price
$0.00 USD
Sale price
$5,920.25 USD
Unit price
per
Taxes included.
Shipping calculated at checkout.
Couldn't load pickup availability
Model: GDL120-30-18Z/5.5
Diameter (mm): 120
Speed regulation mode: The three-phase output inverter can change the spindle speed by changing the frequency of the inverter.
Cooling method: water cooling
Power: 5.5 kw
Voltage: 380 V
Current: 11 A
Torque: 2.65 NM
Frequency:600 HZ
Speed: 18000 RPM
Number of poles: 4 P
Phase： 3 phase asynchronous driver
Rotation: Seen from the shaft end, it rotates counterclockwise
Tool handle: BT30 ER32
Pull stud: BT30-45°
Grease lubrication
Main use: Carving wood, bamboo, ordinary PCB, PVC, PMMA, plastic, two-color board (ABS) and other non-metals.
Diameter (mm): 120
Speed regulation mode: The three-phase output inverter can change the spindle speed by changing the frequency of the inverter.
Cooling method: water cooling
Power: 5.5 kw
Voltage: 380 V
Current: 11 A
Torque: 2.65 NM
Frequency:600 HZ
Speed: 18000 RPM
Number of poles: 4 P
Phase： 3 phase asynchronous driver
Rotation: Seen from the shaft end, it rotates counterclockwise
Tool handle: BT30 ER32
Pull stud: BT30-45°
Grease lubrication
Main use: Carving wood, bamboo, ordinary PCB, PVC, PMMA, plastic, two-color board (ABS) and other non-metals.
1. Power cord: Three-color wire connects to U, V, W phase/yellow-green wire to ground
Temperature control line: 110℃ thermistor two-phase connected to temperature control protector
2. Cooling water outlet :(end 2 and 6 connect 8/6 hose)
3. Knife change and dust removal pressure: 0.2-0.3MPa (6/4 hose)
4. Air seal pressure: 0.1-0.2MPa (6/4 hose)
5,Unloader inlet pressure: 0.70MPa (6/4 hose)
6. Cooling water inlet: pump head 12m (do not connect wrong!)
7. number of proximity switch: hanging knife and unloading knife two NPN(normally open) N.O
Proximity switch connection: brown wire connection +24VDC blue wire connection 0VDC
Signal load is connected to +24VDC at one end/black wire at the other end
Temperature control line: 110℃ thermistor two-phase connected to temperature control protector
2. Cooling water outlet :(end 2 and 6 connect 8/6 hose)
3. Knife change and dust removal pressure: 0.2-0.3MPa (6/4 hose)
4. Air seal pressure: 0.1-0.2MPa (6/4 hose)
5,Unloader inlet pressure: 0.70MPa (6/4 hose)
6. Cooling water inlet: pump head 12m (do not connect wrong!)
7. number of proximity switch: hanging knife and unloading knife two NPN(normally open) N.O
Proximity switch connection: brown wire connection +24VDC blue wire connection 0VDC
Signal load is connected to +24VDC at one end/black wire at the other end
1.Double sealing and air sealing structure
Unique double sealing air seal structure greatly improves the dust-proof and waterproof performance, widely used in copper,aluminum, steel and other gold, is a fine carving processing center field of carving and cutting and stone and CNC .
2.Equipped with standard BT30 taper holes
The shaft ends are connected with standard BT30 taper holes. The spindle adopts 4 imported high-precision P4 bearings, which effectively ensures the operation and machining accuracy of the spindle
●The working environment temperature of the spindle is usually -10~40.
●Before installing the first electric spindle, pls rotate the spindle head by hand, make sure it is flexibility and no blockage.
●Before installing the first electric spindle, pls rotate the spindle head by hand, make sure it is flexibility and no blockage.
P4 fully sealed angular contact ceramic bearings can extend the service life of the spindle.
The longer the length, the greater the torque and power.
Carefully assemble it makes the spindle more precise.
The accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm
1. Our main shaft uses 4 bearings.
2. Bearings are resistant to high temperature and low heat
3. Ceramic ball bearings have low friction, low noise and long service life.
The longer the length, the greater the torque and power.
Carefully assemble it makes the spindle more precise.
The accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm
1. Our main shaft uses 4 bearings.
2. Bearings are resistant to high temperature and low heat
3. Ceramic ball bearings have low friction, low noise and long service life.
●The water-cooled spindle must be used together with the water pump. Otherwise, the spindle will quickly break.
●The AC spindle motor must be used together with the inverter. The power of the inverter needs to be equal to or greater than the power of the spindle. Before use, please set the inverter parameters suitable for the spindle. Otherwise, the spindle and inverter will break immediately.
●When using the spindle, the sound is different from before, so please stop the spindle immediately and replace the spindle bearing.
●The AC spindle motor must be used together with the inverter. The power of the inverter needs to be equal to or greater than the power of the spindle. Before use, please set the inverter parameters suitable for the spindle. Otherwise, the spindle and inverter will break immediately.
●When using the spindle, the sound is different from before, so please stop the spindle immediately and replace the spindle bearing.
1. The electric spindle must be installed in the clamping position, otherwise it is easy damage the bearing!
2. The spindle must be completely stopped to change the tool, and the manual tool change button must not work when the spindle is rotating, otherwise it is easy to cause the spindle to jam!
3. The compressed air must be clean and dry, with a filtration accuracy of 0.1 micron! The air seal is normally open. It is
recommended to use two-stage filtration. The filtration accuracy is 0.5 micron/0.1 micron, and the air filter is equipped with a self-draining device.
2. The spindle must be completely stopped to change the tool, and the manual tool change button must not work when the spindle is rotating, otherwise it is easy to cause the spindle to jam!
3. The compressed air must be clean and dry, with a filtration accuracy of 0.1 micron! The air seal is normally open. It is
recommended to use two-stage filtration. The filtration accuracy is 0.5 micron/0.1 micron, and the air filter is equipped with a self-draining device.
Company information and contact information
Jinan Hongyang CNC Machinery Co., Ltd. was established in 2015. There are more than 100 employees, and the inventory area is 10,000 square meters. It is mainly engaged in engraving machine parts, including spindle motor, frequency converter, stepper motor, drive, hybrid servo motor, servo motor, Richauto dsp series controller, weihong or nc studio controller, spindle cooling water pump, lubricating oil pump, tool sensor, Limit sensors, water-cooled vacuum pumps, air-cooled vacuum pumps, power supplies, transformers, gear boxes, racks, rails, sliders or blocks, ISO30 tool clips, cable chains, spindle dust covers, vacuum cleaners and other engraving machine accessories, welcome your For inquiries.
Contact information
Tiny Wechat Whatsapp Cell Phone 8615098715557
Sales@hycncrouter.com
Contact information
Tiny Wechat Whatsapp Cell Phone 8615098715557
Sales@hycncrouter.com
